Horizontal Milling

The supporting structure is particularly sturdy and consist of modules of pearlitic GG-26 cast iron; they are largely dimensioned and strongly ribbed.

    • Support arm for head .
    • Electrical equipment on a panel easily inspectionable and executed following the international laws
    • Cutter arbor with fixing tie rod and relative support rest/s
    • Centralised lubrication for ways and screws by manual pump.
    • Coolant plant with electropump
    • Safety device for stopping movements in case of overload
    • Prevention protections with micro-switch.
  • All machines are in conformity with CE regulations

Technical Parameters

Model FU 1S FU 1E FU 2
Table; working surface   (mm) 1200 x 250 1300 x 300 1400 x 300
No. of T-slots (mm) 3 / 14 H7 3 / 16 H7 5 / 16 H7
Distance between T-slots 63 60 60
Rotary movement of table in both directions (opt) + 45° + 45° + 45°
Automatic longitudinal (mm) 900 970 1100
Automatic Cross (mm) 250 315 325
Automatic Vertical (mm) 450 450 500
Available distance from spindle to overarm  (mm) 140 140 140
Spindle Spindle speed (rpm) 50 – 1700 (50 Hz) 50 – 1700 (50 Hz) 40 – 1800 (50 Hz)
Spindle speed ranges  (N°) 12 12 12
Spindle taper ISO 40 ISO 40 ISO 40/50*
Diameter of main shaft (mm) 88.88 88.88 88.88 – 128.57
Feeds Longitudinal and cross feed (mm/min) 16  – 340 16  – 1080 10  – 600
Vertical feed (mm/min) 6 – 115 6 – 360 3.3 – 200
No. of feeds (mm) 9 18 18
Quick Tranverse Longitudinal and cross (mm/min) 2000 2000 2300
Vertical (mm/min) 650 650 800
Main motor (Hp) 4.0 5.5 7.5
Feed motor (Hp) 1.5 1.5 2.0
Cooling pump motor (Hp) 0.1 0.1 0.1
Net Weight (kg) 1450 1800 2400

* in option

Universal Milling

This milling machines uses a special high-strength gray cast iron produced by the Meehanite process and whose physical and chemical properties provide low damping capacity, high modulus of elasticity, and excellent wear characteristics.

    • Swivel table + 45°
    • ·  3 axis rapid traverse
    • Flood coolant system
    • Spindle brake
    • Low voltage controls
    • Auto lubrication system
    • Pendant controls.
    • Climb milling control
    • Variable feeds in 3 axis
    • Hardened and ground ways
  • All machines are in conformity with CE regulations

Technical Parameters

Model FU 125E FU 152E FU 152S
Table; working surface   (mm) 1250 x 280 1525 x 325 1525 x 325
No. of T-slots (mm) 3 / 16 3 / 16 5 / 16
Distance between T-slots 63 80 80
Rotary movement of table in both directions (opt) + 45° + 45° + 45°
Automatic longitudinal (mm) 851 1050 1050
Automatic Cross (mm) 290 330 330
Automatic Vertical (mm) 475 475 475
Available distance from spindle to overarm  (mm) 147 147 147
Spindle Spindle speed (rpm) 35 – 1800 (50 Hz) 35 – 1800 (50 Hz) 35 – 1800 (50 Hz)
Spindle speed ranges  (N°) Variable Variable Variable
Spindle taper ISO 40 ISO 40 ISO 40
Diameter of main spindle (mm) 88.88 88.88 88.88
Feeds Longitudinal and cross feed (mm/min) 0  + 1300 0  + 920 10  +  920
Vertical feed (mm/min) 0 + 390 0 + 276 0 + 276
No. of feeds (mm) Cont. Variable Speed Variable Speed Variable Speed
Quick Tranverse Longitudinal and cross (mm/min) 2500 2500 2500
Vertical (mm/min) 750 750 750
Main motor (Hp) 5.5 7.5 7.5
Feed motor (Hp) 2.0 2.5 2.5
Cooling pump motor (Hp) 0.12 0.12 0.12
RAM Mounted Head – FUTV Power over RAM
Ram travel (mm) 550
Spindle Taper R8 or ISO 40 ISO 40
Number of speeds Variable Cont. Variable Speed
Speed Range (rpm) Low  60 – 490  /  High  490 – 4200 35 + 1800
Main motor  (Hp) 4 5.5
Working Feeds – Quick Traverses (rpm) 0 + 1300/1500
Net Weight (kg) 1800 2600 2900

* in option

Vertical Milling

High precision and manoeuvrability are the main qualities of our turret milling machines. They have been constructed with the most advanced technologies and with peculiar attention in the use of materials.

    • High speed head with speed variator .
    • Manual axis feeds
    • Prismatic slideways with scraped planes
    • Slideways protection by special scrapers
    • Centralised lubrication for ways and screws by manual pump.
    • Spindle start/stop pushbutton incorporated in the head
    • Coolant plant with electropump
    • Chip tray
    • Prevention protections with micro-switch.
    • Tie rod
    • All machines are in conformity with prevailing VDE and CE regulations

Optional

    • Mechanical feeds for independent longitudinal, transversal or vertical axis (feeds n° 8 from

20 – 550mm/min ; rapid 850 – 750mm/min; power 0.37 kW).

    • Electronic feeds for independent longitudinal, transversal or vertical axis
    • Ballscrews
    • Hardened slideways
    • Pneumatic tool locking.
    • Digital readout on 2, 3 or 4 axes
    • Devices for special milling (at right angle or multiangular)
    • Automatic centralized lubrication of slideways
    • Slideways protection bellows.
    • Dividers, vices, boring head, etc.
    • All machines are in conformity with prevailing VDE and CE regulations

Technical Parameters

Model FTV 1 FTV 2 FTV 3
Table; working surface   (mm) 1118 x 254 1270 x 254 1370 x 280
No. of T-slots (mm) 3 / 16 3 / 16 3 / 16
Distance between T-slots 63 63 63
Longitudinal manual  (mm) 750 830 840
Longitudinal travel with Power feed (mm) 665 745 755
Cross (mm) 406 406 375
Vertical (mm) 406 406 406
Ram (mm) 570 570 570
Head Spindle speed (rpm) 50 – 3750 (50 Hz) 50 – 3750 (50 Hz) 50 – 3750 (50 Hz)
Spindle speed ranges  (N°) 2 2 2
1st range (rpm) 50 – 410 (50 Hz) 50 – 410 (50 Hz) 50 – 410 (50 Hz)
2nd range (rpm) 410 – 3750 (50 Hz) 410 – 3750 (50 Hz) 410 – 3750 (50 Hz)
Head moves right and left 90° 90° 90°
Head tilts front to back 45° 45° 45°
Quill Power feed per revolution (mm/rpm) 0.04 – 0.08 – 0.16 0.04 – 0.08 – 0.16 0.04 – 0.08 – 0.16
Spindle taper ISO 30/40* ISO 30/40* ISO 40
Quill diameter (mm) 85.7 85.7 85.7
Quill travel (mm) 127 127 127
Min/max distance from spindle center to the body (mm) 165 – 735 165 – 735 125 – 695
Max. distance from spindle to table (mm) 465 465 470
Main motor (Hp) 3 3 3
Cooling pump motor (Hp) 0.8 0.8 0.8
Maximum work piece weight (kg) 200 200 250
Net Weight (kg) 1050 1100 1400

* in option