Analog Rockwell

Acting the hand wheel on the base will move the indenter to the test block and acting up lever will implement the load force for the test cycle.

    • Can be used with all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing
    • Simple to use
    • The test forces are controlled test by test through load cell and closed loop AFFRI system to assure high performance conform to ISO standards
    • Perfect and effective measurements even at the first test with AFFRI® system inside.
    • Accuracy is stable in every condition.
    • No need to be leveled when installed

Technical Parameters    

Model 206 RT 206 RTS
Preload ( kgf ) 10 3
( N ) 98.07 29.4
Rockwell loads ( kgf ) 60 ,  100 ,  150
( N ) 588 ,  980 ,  1471
SuperRockwell loads ( kgf )   15 ,  30 , 45
( N ) 147 ,  294 ,  441
 Brinell loads ( kgf ) 6.25 ,  125 , 187.5 15.6 , 31.2
( N ) 61.2 ,  1225 , 1839 153 , 306
Vickers knoop loads ( kgf ) 10 , 60 , 100 3 , 15 , 30
( N ) 98.07 , 588 ,  980 29 , 147 , 294
Reading resolution 0.5 HR
Accuracy Conformation standards EN-ISO 6506-2/ 6507-2/ 6508-2/ ASTM-E18
Mode of Operation manual
Diameter of column 60mm
Diameter of anvil 60mm
Total height capacity 215 mm
Total depth capacity 190mm
Max load of test piece 1000 kg
Net Weight (kg) 65

Automatic Rockwell

A single input to start in automatic sequence without interruption applies the minor and major load and measure the Rockwell indentation automatically. All test operations are managed through a single start command to reduce operator fatigue and to increase test repeatability and accuracy to the maximum.

    • Can be used with all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastics.
    • The system is capable of measuring accurately even if the test piece defects up to 50mm during measurement. This automatic compensation provide accurate results under adverse test conditions
    • External source of vibration do not create any influence on result.
    • The test piece is clamped automatically and locked in position before the test force (20-400 kgf) is applied.
    • The test forces are controlled test by test through load cell and closed loop AFFRI system to assure high performance conform to ISO standards
    • Perfect and effective measurements even at the first test with AFFRI® system inside.
    • Accuracy is stable in every condition.
    • No need to be leveled when installed
    • It can be utilized by everybody , only one start input and wait for test results.
  • An emergency push button is also included

Technical Parameters    

Model   3302 MRS 250 MRS  3332 MRS
Preload ( kgf ) 10 – 3
( N ) 98.07 – 29.4
Rockwell loads ( kgf ) 10,  60,  100,  150
( N ) 98.10, 588.60,  981,  1471.50
SuperRockwell loads ( kgf ) 3,  15,  30, 45
( N ) 29.43, 147.15, 294.30, 441.45
 Brinell loads ( kgf ) 5, 6.25, 10, 15.6, 25, 30, 31.2, 62.5, 125, 187.5
( N ) 49.05, 61.3, 98.1, 153.23, 245, 294.43, 306.5, 613, 1226, 1839
Vickers knoop loads ( kgf ) 3, 5, 10, 15, 20, 30, 60, 100
( N ) 29.43, 49.05, 98.1, 147.15, 196, 294.3, 588.6, 981
For plastics, rubber as per EN-ISO 2039 ( kgf ) 250 or 2452.5 N Brinell
( N ) 49, 132, 358, 961
Shore A – B – C – D
Accuracy Conformation standards EN-ISO 6506-2/ 6507-2/ 6508-2/ ASTM-E18 – EN-ISO 2039
Mode of Operation Automatic with load cell and closed loop Affri patent
Mobile indenter From 0 – 400mm From 0 – 50mm
Self clamping 100N 200 or 4000N
Total height capacity 400mm motorized 400mm manual 215 mm
Total depth capacity 200mm 190mm
Max load of test piece 2000 kg 1000 kg
Net Weight (kg) 120 100 75
TypeTmax
°C
Capacity
litre
Ext dimension
(wxhxd) mm
Int dimension
(wxhxd) mm
ShelvesPower
kW
Voltage
Volt
Weight
kg

Digital Rockwell

Acting the hand wheel on the base will move the indenter to the test block and acting up lever will implement the load force for the test cycle.

    • Can be used with all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing.
    • Simple to use
    • The test forces are controlled test by test through load cell and closed loop AFFRI system to assure high performance conform to ISO standards
    • Perfect and effective measurements even at the first test with AFFRI® system inside.
    • Accuracy is stable in every condition.
  • No need to be leveled when installed

Technical Parameters    

Model 206 RTD 206 RTSD 206 EX 206 EXS
Preload ( kgf ) 10 3 10 3
( N ) 98.07 29.4 98.07 29.4
Rockwell loads ( kgf ) 60 ,  100 ,  150 60 ,  100 ,  150
( N ) 588 ,  980 ,  1471 588 ,  980 ,  1471
SuperRockwell loads ( kgf ) 15 ,  30 , 45 15 ,  30 , 45
( N ) 147 ,  294 ,  441 147 ,  294 ,  441
 Brinell loads ( kgf ) 6.25 ,  125 , 187.5 15.6 , 31.2
( N ) 61.2 ,  1225 , 1839 153 , 306
Vickers knoop loads ( kgf ) 10 , 60 , 100 3 , 15 , 30 10 , 60 3 , 15 , 30
( N ) 98.07 , 588 ,  980 29 , 147 , 294 98.07 , 588 29 , 147 , 294
Reading resolution 0.1 HR 0.2 HR 0.1 HR 0.2 HR
Accuracy Conformation standards EN-ISO 6506-2/ 6507-2/ 6508-2/ ASTM-E18 Conformation standards

EN-ISO 6506-2/  6508-2

Mode of Operation manual
Diameter of column 60mm
Diameter of anvil 60mm
Total height capacity 215 mm
Total depth capacity 190mm
Max load of test piece 1000 kg
Net Weight (kg) 65

Micro Vickers

A digital micro hardness tester with very large color screen and friendly with integrated functions. Ideal for factory and laboratory use. It indicates load force applied, load time, diagonal 1 and diagonal 2, hardness results, number of measurements stored, averages, statistics and self conversion data, setup utility and many friendly functions.

    • Can be used with all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing
    • Load mechanism with no fluctuation
    • HK Knoop test can be calculated just by selecting switch and apply extra Knoop indenter
    • Correspondence of automation through RS232C or other serial output.
    • Accuracy is stable in every condition.
  • Easy operation and multi scale readout

Technical Parameters 

  

Model DM-2A DM-2D DM-8A DM-8B
Test load 10, 25, 50, 100, 200, 300, 500, 1000 5, 10, 25, 50, 100, 200, 300, 500, 1000 1, 3, 5, 10, 25, 50, 10,, 200, 300, 500, 1000, 2000
Dwell Time 5 – 40sec 5 – 60sec 5 – 60sec
Read out Analogic Digital Digital – touch panel
Data output Centronics RS 232C
Magnification 100x – 400x
Max height of specimen 95mm 120mm
Max depth of specimen 100mm 160mm
Measuring microscope Max length 250μm 250μm
graduation 0.5μm 0.1μm 0.01μm
Switch objective/indenter Auto turret
Accuracy Conformation standards EN-ISO 6507-2/  ASTM E-384/ JIS B 7734
Loading mechanism Auto loading and releasing
Load applying speed 50μm/sec
Net Weight (kg) 28
TypeTmax
°C
Capacity
litre
Ext dimension
(wxhxd) mm
Int dimension
(wxhxd) mm
ShelvesPower
kW
Voltage
Volt
Weight
kg

Portable

A portable hardness tester with direct digital readout. It is designed for hardness tests on particularly cumbersome items, materials in the warehouse, and pieces which cannot be tested on a bench hardness tester. Very light and compact with microprocessor incorporated; LCD display indicating the hardness value which remains fixed and memorized on the display until the next test.

    • Can be used with all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing
    • Suitable for flat, round and irregular pieces
    • No need to adjust it
    • Perfect and effective measurements even at the first test with AFFRI® system inside.
    • Accuracy is stable in every condition.
  • For thin surfaces; up to 0.08mm thickness and large parts

Technical Parameters  

Model Metaltester MK II
HRC Rockwell C 0 – 80
HRB Rockwell B 27 – 99
HB5 Brinell 5 25 – 205
HB30 Brinell 30 66 – 600
HV Vickers 66 – 1800
R Tensile module Nmm2 270 – 800
HR15N Rockwell HR15N 69 – 93
Reading resolution 0.1 HR
Memory of test results 300 tests
Data transmission RS 232C
Operating time 1000 tests
Automatic shut off After a pause of 2 min, reactivate by button
Statistics of results Means of results
Dimension of probe Body: Ø40 mm x 90 mm; Base Ø20mm
Net Weight (kg) Probe – 300g , Digital box – 980g, Carrying case – 2.5kg

Universal Rockwell Brinell

The universal automatic hardness tester uses only one drive starts up and performs , without a break, the phase positioning, approach and execution of the test for all Rockwell, Brinell and Vickers test.

    • Absolute precision.
    • Unparallel accuracy , repeatability and reproductivity
    • Automatic control and selection of pre-loads and loads
    • Perfect and effective measurements even at the first test with AFFRI® system inside.
    • Universal use.
    • High resolution of measure 0.1 HRC or 0.01 HRC on demand
    • 2 years full waranty.

Technical Parameters    

Model 251 VRSD 251 VRSA 251 VRSTV 270 VRSD 270 VRSA 270 VRSTV
Vickers Knoop Load ( kgf ) 1, 2, 3, 5, 10, 20, 30, 50, 100
( N ) 9.81, 19.62, 29.43, 49.05, 98.1, 196.2, 294.3, 490.5, 981
Rockwell loads ( kgf ) 10 , 60 ,  100 ,  150
( N ) 98.1 , 588 ,  980 ,  1471
SuperRockwell loads ( kgf ) 3 , 15 ,  30 , 45
( N ) 29.43 , 147 ,  294 ,  441
 Brinell loads ( kgf ) 5 , 6.25 , 10 , 15.6 , 25 , 30 , 31.2 , 62.5 ,  125 , 187.5
( N ) 49.05 , 61.3 , 98.1 , 153.23 , 245 , 294.43 , 306.5 , 613 , 1226 , 1839
Optional test for plastic or rubber ( N ) 49 , 132 , 358 , 961
Shore A – B – C – D
Reading resolution 0.1 HR
Reading Digital encoder for Brinell – Vickers Drum scale + digital readout CCD camera + computer Digital encoder for Brinell – Vickers Drum scale + digital readout CCD camera + computer
Magnification 75x  150x  220x  300x 75x  150x  225x  300x
Accuracy Conformation standards EN-ISO 6506-2/ 6507-2/ UNI EN 10109/ ASTM-E18
Self aligning to test surface From 0 – 50mm From 0 – 400mm
Mobile indenter From 0 – 50mm From 0 – 400mm multiple till 400mm
Mobile clamping From 0 – 50mm From 0 – 400mm multiple till 400mm
Total height capacity 200 mm
Total depth capacity 190mm
Max load of test piece 1000 kg
Net Weight (kg) 75 150 95
TypeTmax
°C
Capacity
litre
Ext dimension
(wxhxd) mm
Int dimension
(wxhxd) mm
ShelvesPower
kW
Voltage
Volt
Weight
kg